Dci-products SmartRidge II Bedienungsanleitung PDF herunterladen

Questions or Concerns?

Call us Toll Free

1-800-622-4455

We’ll Be There To Help You!

Fig. A

Fig. B

Fig. E

Fig. F

Fig. G

Fig. C

Fig. D

STEP  Prepare Roof Decking

The first step installing SmartRidge II is to prepare the roof decking by cutting or leaving a 1” slit

(do not cut at least 12” in from the gable ends or other obstacles) on both sides of the roof peak

away from any ridge beam. This is most easily done when laying the roof decking by cutting the

last piece of roof decking 1 ½” short of the roof peak (Fig A).

Note: The proper amount of soffit ventilation is required to maximize SmartRidge II’s

effectiveness. Ask us about our revolutionary soffit venting system called SmartVent.

STEP  Attach SmartRidge II End Piece

After roof shingles are installed, begin at one end of the roof. A nailing strip can be found on

SmartRidge II approximately 2" in from the edge of the product. This is where you should nail

when attaching SmartRidge II to the roof decking using 1 ½” – 2” roofing nails.

In the SmartRidge II box are pieces of fabric (approx. 10 ½” square) and two end caps that will be

used to seal the gable ends (Fig B). Install end caps or wrap the fabric around the end of a piece of

SmartRidge II so that an equal amount of fabric is on top and on the bottom (Fig C).

Position the SmartRidge II piece over the ridge so that it is nearly

centered over the ridge opening. Butt the SmartRidge II against the

end cap or, if using the fabric pieces to seal the end, wrap the fabric

tightly around the end of the SmartRidge II piece (Fig D). Fold

SmartRidge II over the ridge and secure to the roof decking using

1 ½” roofing nails minimum. Other installation techniques are

available by calling DCI at 1-800-622-4455 (engineering

department).

STEP  Attach Remaining SmartRidge II Pieces

Attaching the next pieces of SmartRidge II can be done by butting the end of the next piece up

tightly against the end of the previously installed piece (Fig E). Continue butting 3’ pieces of

SmartRidge II until you reach the end of the roof. Cut the final piece to fit flush with gable end cap

and/or repeat step 2 to seal the end & install gable end fabric.

STEP  Install Cap Shingles

Install cap shingles over SmartRidge II as you normally would (Fig F).

Note: For aesthetic purposes, you can extend SmartRidge II all the

way to the end of the gable roof (Fig G). SmartRidge II is strong

enough to stand up to nail guns during shingle installation and use

extra long roof nails (1 ½” to 2” nails) for securing the shingles.

Nails should penetrate through roof deck.

www.dciproducts.com

Installation Instructions

(800) 622-4455

(610) 622-4038 FAX

1 2

Inhaltsverzeichnis

Seite 1 - 1-800-622-4455

Questions or Concerns? Call us Toll Free 1-800-622-4455 We’ll Be There To Help You! Fig. A Fig. B Fig. E Fig. F Fig. G Fig. C Fig. D STEP  Pr

Seite 2 -  Prepara el Techo (Fig. A)

(800) 622-4455 (888) 356-3291 FAX ¿Preguntas? Llama: 1-800-622-4455 www.dciproducts.com ¡Estaremos Allí Para Ayudarte! PASO  Prepara el Tec

Kommentare zu diesen Handbüchern

Keine Kommentare

Dci-products SmartRidge II Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für Zuhause Dci-products SmartRidge II herunter. DCI Products SmartRidge II User Manual [en] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für Zuhause Dci-products SmartRidge II